Quality US manufactured plastic transmission covers to suit Triumph Spitfire & early Triumph Heralds.
Brand new, imported from the US manufacturer.
The covers are pre drilled & easier to work with & fit better than most fibreglass versions.The covers are $185.00 & can be sent via Aust. Post for $25.00 to most Australian addresses.
Seal kits also available for an extra $30, but can be sent with the cover to save postage costs.

Transmission Cover for TR4 - 6
Quality US manufactured transmission covers to suit Triumph TR4, 4A, 5 & 6.
Brand new imported from the US manufacturer.
The covers are pre drilled & easier to work with than most fibreglass versions.The one-piece models are stiff, bulky, and unwieldy. All gearbox covers including this one can be challenging to install, especially at the firewall, but at least this part is easier to maneuver into position before fastening. Getting the one-piece units in and out several times during fitting is truly maddening! Importantly, this part is made of tough and flexible polyethylene--not stiff ABS--so making this part conform to YOUR car is much enhanced.$195.00 plus post $25.00

One length of THIN gasket for tunnel and firewall arches, and One length of THICK gasket for sealing to floorpans.
This is not as nice as the original OEM molded foam pieces, but this is the best (only) one we find out there.
Fits Triumph TR2 through to TR6 and Spitfire (1962-1980)The kits are $30.00 + postage $13.90

This quality product is imported from the US Manufacturers.The console has two storage compartments to provide much-needed small storage space. The shallow compartment up front (over the handbrake) is suitable for mobile phone, charger, small change, wallet, etc. The deep compartment in rear is suitable for larger items such as GPS, sunglasses case, gloves, torch, etc.Finally, two power outlets with covers come standard for powering your GPS, Phone, iPad, etc.$400.00 plus postage of $22.85

This kit makes opening the bonnet of your Spitfire & GT6 so much easier. Just received from the US manufacturer.Two powerful gas springs will now make lifting your bonnet a thing of ease! The initial lifting force is substantially reduced, and after opening only a portion, the springs take over completely and raise your bonnet Fully Open.Plus your bonnet now has Even Support, and to reduce the risk of it crashing down.Lowering the bonnet is so much better, too! The weight does not build and build like before, but instead you "pull" the bonnet down and then lower it for only the last portion while the springs help counterbalance the weight!This cleverly engineered design requires NO DRILLING. Custom fabricated brackets and ball studs fasten to existing geometry. Gas Springs have even been custom made for just this application--they are not "off the shelf."Treat yourself and your Spitfire or GT6 to a little luxury!$125.00 plus postage of $22.85 to Australian addresses.

This strut kit makes opening the bonnet of your Spitfire or GT6 so much easier. Just received from the US manufacturer.
This kit suits Triumph Spitfire from 1962 - 70 & GT6 from 1966 - 70.Two powerful gas springs will now make lifting your bonnet a thing of ease! The initial lifting force is substantially reduced, and after opening only a portion, the springs take over completely and raise your bonnet Fully Open.Plus your bonnet now has Even Support, and to reduce the risk of it crashing down.Lowering the bonnet is so much better, too! The weight does not build and build like before, but instead you "pull" the bonnet down and then lower it for only the last portion while the springs help counterbalance the weight!This cleverly engineered design requires NO DRILLING. Custom fabricated brackets and ball studs fasten to existing geometry. Gas Springs have even been custom made for just this application--they are not "off the shelf."Treat yourself and your Spitfire or GT6 to a little luxury!$135.00 plus postage of $22.85 to Australian addresses.

These Battery Bins are custom moulded to fit chrome-bumper MGB's ('63-'74).No modifications to your MGB are required. Battery Bins slip right into place and are covered by the metal lid.Will support your battery if the battery frame is rusted out!Will fit some 12V Batteries.
Converts extra battery frame into useful storage compartment!$70.00 each
Can be sent via Aust Post for an extra $18.95 to Aust addresses.
Two can be sent for $22.85

These Battery Bins are custom molded to fit rubber-bumper MGB's ('74 1/2 -'80).
No modifications to your MGB are required. Battery Bin slips right into place and is covered by the metal lid.Protect your MGB from battery acid!$80 each & can be posted for an extra $18.95 to Australian Addresses.

Available for MGB's prior to 1972 when the factory added their own console.Attractive. Looks like original equipment. Styled just like the factory consoles that appeared in 1972. Black grained ABS body, and instead of vinyl this armrest is covered with genuine leather. Installs over that sun-bleached bald spot on your tunnel. Comfortable. Finally, a place to rest your arm! Storage Compartment. Cup Holder. You'll wonder how you ever lived without this feature.
Quality. Made with leather and high-impact black grained ABS thermoplastic.Imported from the US manufacturers & available here in Australia for$225.00 each & can be sent to Aust. addresses for $18.95 or $25.70 Express Post

(Note: Photos show MGB, but Sprite/Midget Console is almost identical)This console suits Midgets or Sprites prior to 1972.Attractive. Truly looks like original equipment. Styled just like the factory consoles that appeared in 1972. Black grained ABS body, and instead of vinyl this armrest is covered with genuine leather. Installs over that sun-bleached bald spot on your tunnel.Storage Compartment. You will love having this extra storage compartment for your maps, torch, loose change, driving gloves, etc.Cup Holder, you'll wonder how you ever lived without this feature.
Quality. Made with leather and high-impact black grained ABS thermoplastic.
Imported from the US manufacturers & available here in Australia for$225.00 & able to be sent to Aust. addresses for an additional $18.95 or $23.95 for Express Post

Enhance your MGB with this truly custom Cup Holder!
This suits MGB models from 1972 - 80, with the factory centre console
This is custom molded to fit the trapezoidal-shaped area just in front of the shifter, and looks like original equipment. Made from black, textured ABS just like the console it sits on, it fits two beverages--from small cups and cans to medium sized bottles and mugs.
Manufactured in & imported from the USA.
No fasteners are necessary. Simply set in place, and it is trapped in position. Removal is just as simple.$49.00 eachCan be sent to Aust addresses for an extra $16.95The British Logo stubby holder is available for an extra $10.00

Instant Access to your battery! Just Twist & Lift -- No tools required.
This Cover suits MGB's from mid 1974 - 80.The hinged covers are hand made & powder coated in a semi gloss black finishQuarter-turn DZUS fasteners in the Cover are made of Stainless Steel, and will last forever. Quality made entirely in USA.These Covers work well with the Plastic Battery Bin, but will work just as well without it.$99.00 each plus postage of $21.50 to Aust addresses

Stop marring your expensive knock-offs with every hammer hit! This toolis a full 650 mm long for incredible power, yet is much gentler to your knock-offs.The tool locks onto knock-off (unlike similar competitive tools) so it is very easy to use. Never dent another guard or ruin another spoke with the old hammer technique. This tool generates lots of torque, and gives you control -- you can feel how tight your wheel nut is. No owner or garage should be without it.The tool stores easily in your boot, and is very affordable (much less than the cost of a dented guard repair!). Don't leave home without it!Note: Excessive force should not be used with this tool It is not designed for stuck KO's etc. Do not stand/jump on tool.Fits all vintage MG, Triumph, Austin Healey, Morgan, and Sunbeam factory KO's (Note: does not fit some of the latest reproduction KO's being sold, nor modern Morgan KO's!).$95.00 each & can be sent to Aust addresses for $21.90 or $25.90 Express Post

MG & other British Knock off Tool for Octagonal Knock off NutsA superior tool for removing your wheel nuts! Never ding another guard or dent another wheel with the old hammer-and-stubby-tool technique.This tool generates lots of torque, and gives you control -- you can feel how tight your wheel nut is. This tool will remove stubborn nuts your old spanner struggles with. No owner should be without it.Fits MG, Triumph, Austin Healey, and Sunbeam.The tool stores easily in your boot, and is very affordable (much less than the cost of a dented guard repair!). Don't leave home without it!Note: Excessive force should not be used with this tool. It is not designed for stuck KO's etc. Do not stand/jump on spanner.Wrench measures 70 mm or 2.75" across the flats.$95.00 each & can be posted to Australian addresses for an additional $21.90

This Steering Column Cowl is an exact copy of the original. Will suit all Mk 1 Mini from 1959 - '67.
Quality product imported from the US manufacturers.Manufactured in ABS plastic, with a black gloss finish, as per the original.Cost of the cowl is $80.00 plus postage of $13.90 to Australian addresses.

Stop marring your expensive knock-offs with every hammer hit! This tool is a full 650 mm long for incredible power, yet is much gentler to your knock-offs. The tool locks onto knock-off (unlike similar competitive tools) so it is very easy to use. Never dent another guard or ruin another spoke with the old hammer technique. This tool generates lots of torque, and gives you control -- you can feel how tight your wheel nut is. No owner or workshop should be without it. The tool stores easily in your boot, and is very affordable (much less than the cost of a dented guard repair!).
Fits Jaguar two eared spinners only.
Imported from the US manufacturer & available here in Australia.
Don't leave home without it! Note: Excessive force should not be used with this tool It is not designed for stuck KO's etc.$110.00 each plus postage of $21.90 to Aust addresses

Avoid damaging your wire wheel knock off's
The GENTLEST tool for your knock-offs!
Note: Photo on car shows Jaguar version, but this part fits: MG, Triumph, Austin Healey, Morgan, and Sunbeam.
Even the specialty knock-off hammers will mar and blemish those chrome plated spinners. But fit this high-density, seventeen-layer laminated wood tool over your knock-off and get perfect protection against marring. Nothing else on the market is as soft to your knock-offs, plus this tool gives you more than three times the torque of hitting your knock-off directly! Gentle and powerful!
The tool stores easily in your boot, and is very affordable. Don't leave home without it!
The photos shows the Jaguar version but the MG & other British tool is very similar & suits the smaller spinnersWe've imported a quantity of these from the US manufacturer. The MG tool is $50.00 & the Jaguar tool is $55.00. The tool can be sent to Aust. addresses for an additional $17.50

Avoid damage to your knock off wheel spinners!To avoid damage to your Eared Spinners, fit this high-density, seventeen-layer laminated wood tool over your knock-off and get perfect protection against marring. Nothing else on the market is as soft to your knock-offs, plus this tool gives you more than three times the torque of hitting your knock-off directly! Gentle and powerful!The tool stores easily in your boot, and is very affordable. Don't leave home without it!Fits JAGUAR KO's only!We've imported a quantity of these from the US manufacturer & have them available here in Australia, for $50.00, plus postage of an additional $17.50

Install this kit and your boot lid will smoothly open with just a turn of the key!This premium kit includes a high-quality gas-charged prop and powder coated bracket to provide a smooth, dampened lift action, and an easy non-dampened closing. Almost invisible when installed.Suits 1995 - 2005 modelsThe manufacturers of this kit have been making this high quality kit in the USA for over a decade, and have sold thousands of them wholesale.
Don't be fooled by inferior copies sold by "specialist" suppliers at higher prices.Why pay over $100.00 from others?Note: for heavy spoilers or luggage racks, this Lift Kit may not provide adequate lifting.We've imported a quantity of these from the US manufacturers & can now offer them to Australian MX5 owners for $75.00. We can send them via Australia Post for an additional $17.50

Enhance your MX5 / Miata's good looks and keep out unwanted debris with this Grille!This grille suits 90 - 97 Models.This will also protect both your engine radiator and your air conditioner radiator from damage due to stones and other road debris.These Protective Grilles are made of steel, and have a durable powdercoated - not painted - finish of silver or black. They visually stand out more than the High-Flow Grilles but let plenty of air through, having 58% open area.Installation is easy.Imported from the US manufacturer & now available here in Australia for $49.00 & can be sent to Australian addresses via Australia Post for an additional $17.50

Keep unwanted debris out, with this Grille!New stock just received at reduced price.As well as enhancing your MX5's appearance, it will also protect both your engine radiator and air conditioner condenser from damage due to stones and other road debris.
These Grilles are made of steel with a durable powder coated - not painted - finish.
Available in Black or SilverThis High Flow Grille has 79% open area; for maximum cooling capability. Suits MX5's from 1990 - 97These have been imported from the US Manufacturers & are available here in Australia for $49.00 & can be sent to Australian addresses for $17.50

As well as enhancing your MX5's appearance these will protect both your engine radiator and air conditioner condenser from damage due to stones and other road debris.These Mesh Grilles are made of Aluminium.The kit comes with bolts & mounting blocks.The black ones additionally have a durable powder coated - not painted - finish.These suit MX5's from 1990 - 1997. Imported from the US Manufacturer & available here in Australia for $95.00 & can be sent to Australian addresses for $17.50